- Home
- Care and maintenance of PRIM watches
Care and maintenance of PRIM watches
Instructions for use and basic watch care rules
(standard information after buying a watch)
You have just become the owner of a watch from our collection. To make sure it serves you for a long time and keeps its good looks, a few rules need to be followed – and already when buying, you should choose a watch that suits the way you intend to use it.
The movements used in our watches are either quartz or mechanical.
- Quartz (battery-powered) watches are accurate to about +/- 15 s a month. The battery in these watches usually lasts about 1 – 2 years.
- Unless stated otherwise, watches with a mechanical movement are accurate to +/- 30 s per 24 hours and, when fully wound, should run for at least 10 hours.
The battery is fitted into quartz watches during production. Some time – varying in length – passes before the watch reaches the customer, so it may stop working in less than a year. A flat battery during the warranty period is not grounds for a complaint. Never replace the battery yourself; ask a watch service centre to do it.
The materials and surface finish of the watch, bracelet or strap have a major influence on its price. The highest-quality materials used in watchmaking are 316L stainless steel, titanium and ceramics. Various alloys are less durable. Steel watches are marked Stainless steel or All stainless steel on the caseback. If stainless steel is used only for the caseback, it says Stainless steel back. Watches made of alloy are unmarked or carry the words Base metal. Titanium materials are marked Titanium. With careful handling, 316L steel watches last almost indefinitely and do not corrode. By contrast, alloy watches can start to corrode within a very short time. Wear can become visible on watches made of the cheapest materials within just a few months. Corrosion shows up as discolouration or flaking of the material. How long it takes for wear to appear varies from person to person and depends on how the watch is used and, above all, on how aggressive the owner's sweat is. As a rule, only higher-priced watches that use the most advanced plating technologies (PVD, IPG,…) keep their surface unchanged for several years. Changes in the watch's surface, colour shade or lustre are caused by gradual wear of the materials used. This is wear resulting from normal use of the product. These changes may occur well within the warranty period.
The quality of the crystal on a watch is in proportion to its price. Sapphire crystals are the most expensive and of the highest quality. They are followed by mineral crystals with various surface treatments, ordinary glass, and the softest are plastic substitutes. Bear in mind, however, that even the hardest crystals can be broken or scratched by careless handling. A scratched, broken or cracked crystal is considered mechanical damage and is not grounds for a complaint.
Fashion watches often have various decorative elements on their surface, glass components (Swarovski, Preciosa,…) or cubic zirconia. These watches are intended for occasional wear and are not at all suitable for sport, housework or other physical activity in which the watch could be knocked or come into contact with water or another liquid. In particular, chemicals contained in cosmetics, hairspray, perfume and the like dissolve the adhesives that hold the stones, causing the glued components to come loose and flake off. Even if marked as water-resistant, such watches should not come into contact with water! We recommend taking these watches off even when washing your hands. Stones coming loose is usually caused by unsuitable use. A knock to the decorative elements will in many cases loosen them so that they eventually fall out.
Straps are the part of the watch under the most strain. How long they last depends on how the watch is used. A strap may have a shorter life than the warranty period. Wear of the strap and its replacement within the warranty period is not grounds for a complaint. In most cases a worn strap can be replaced with an original or non-original part.
Cleaning and caring for your watch – you can clean the watch with a soft, dry cloth. Rinse a water-resistant watch with water and wipe it dry. Never use any solvents! Never clean the watch in an ultrasonic cleaner! If the watch is very dirty, ask a service centre to clean it thoroughly. Mechanical watches should be taken to a service centre at least once every two years to be checked, cleaned and regulated.
Warning: If your watch comes with its own operating instructions, please follow them!!!
Basic watch care rules
- keep your watch clean
- have the water resistance checked regularly at a service centre
- have the automatic movement cleaned and re-oiled regularly (done as part of a full service every 2-5 years)
- try to avoid hard knocks
- do not expose the watch to very hot or salt water unnecessarily
- on quartz watches, keep an eye on battery life
- do not expose the watch to magnetic fields for long periods (e.g. speakers, electronics).
- follow the rule – never turn the hands backwards and never change the date or day between 21:00 and 3:00 (this can damage the movement)
Operating instructions by movement
PRIM battery movements (cal. 38, 39, 48)
Setting the time
On watches with a screw-down crown, first unscrew the crown by turning it towards you.
When the seconds hand reaches 12 o'clock, pull the crown out to the second position. This stops the watch; then set the time by turning the crown as follows. Turn the hands clockwise, first setting the minute hand about 5 minutes past the desired time, then go back to the desired time.
On watches with a date, first move the hands past 12 o'clock. Whether or not the date changes tells you if the watch is showing morning or afternoon.
To restart the watch and keep it working properly and water-resistant after setting, push the crown back into position 0. On watches with a screw-down crown, screw it back down.
Setting the date
Do not change the date between 21:00 and 3:00, so that the date changeover is not disrupted.
To set the date, pull the crown out to the first position and turn it away from you.
To keep the watch working properly and water-resistant after setting, push the crown back into position 0. On watches with a screw-down crown, screw it back down.
Warning: Protect the watch from shocks, impacts, magnetic fields and temperatures below -10 °C and above 50 °C.
PRIM hand-wound mechanical movements (cal. 93, 94, 103)
Starting the watch
On watches with a screw-down crown, first unscrew the crown by turning it towards you.
To start the watch, turn the crown in position 0 away from you. Wind it until you feel clear resistance, ideally every morning.
If you do not wear the watch for a long time, we recommend winding it about once a month and letting it run down.
PRIM self-winding mechanical movements (cal. 95, 98, 105)
Starting the watch
On watches with a screw-down crown, first unscrew the crown by turning it towards you.
To start the watch, turn the crown in position 0 away from you (5-10 turns).
After that, they wind themselves with the movement of your wrist.
If you do not wear the watch for a long time, we recommend getting it going about once a month by wearing it or with the crown (10–15 turns).
We recommend fully winding the watch with the crown (by hand) only occasionally.
If you use a watch winder, we recommend following these guidelines:
- Choose a programme of 800-950 turns per day, anticlockwise.
- The winder should have a programme with a pause, e.g. switching off at night (8–12 hours). If it does not, switch it off at night yourself but increase the number of turns by about half.
- Continuous winding can cause excessive wear of or damage to the self-winding mechanism and, in exceptional cases, damage to other parts of the movement.
Setting the time
PRIM movements without date, cal. 93, 95, 103, 105
On watches with a screw-down crown, first unscrew the crown by turning it towards you.
When the seconds hand reaches 12 o'clock, pull the crown out to the second position. This stops the watch; then set the time by turning the crown.
To restart the watch and keep it working properly and water-resistant after setting, push the crown back into position 0. On watches with a screw-down crown, screw it back down.
PRIM movements with date, cal. 98, 94
On watches with a screw-down crown, first unscrew the crown by turning it towards you.
When the seconds hand reaches 12 o'clock, pull the crown out to position 1. This stops the watch. Turn the crown to move the hands clockwise until the date changes. Set the desired date by repeatedly moving the hands back and forth between 23:10 and 00:10. Once the desired date is reached, continue moving the hands clockwise to the desired time.
To restart the watch and keep it working properly and water-resistant after setting, push the crown back into position 0. On watches with a screw-down crown, screw it back down.
Warning: Protect the watch from shocks, impacts, magnetic fields and temperatures below -10 °C and above 50 °C. ! The recommended service interval is 3 years.
Swiss automatic movement cal. 71 / cal. 73 (ETA 2824-2 / Sellita SW200-1)
On watches with a screw-down crown, first unscrew the crown by turning it towards you.
To start the watch, turn the crown in position 0 away from you (5-10 turns).
After that, they wind themselves with the movement of your wrist.
Setting the time
On watches with a screw-down crown, first unscrew the crown by turning it towards you.
When the seconds hand reaches 12 o'clock, pull the crown out to the second position. This stops the watch; then set the time by turning the crown. Turn the hands clockwise, first setting the minute hand about 5 minutes past the desired time, then go back to the desired time.
On watches with a date, first move the hands past 12 o'clock. Whether or not the date changes tells you if the watch is showing morning or afternoon.
To restart the watch and keep it working properly and water-resistant after setting, push the crown back into position 0. On watches with a screw-down crown, screw it back down.
Setting the date
Do not change the date between 21:00 and 3:00, so that the date changeover is not disrupted.
To set the date, pull the crown out to the first position and turn it away from you.
To keep the watch working properly and water-resistant after setting, push the crown back into position 0. On watches with a screw-down crown, screw it back down.
If you do not wear the watch for a long time, we recommend getting it going about once a month by wearing it or winding it with the crown (10–15 turns). We recommend full manual winding only occasionally.
If you use a watch winder, we recommend following these guidelines:
- Choose a programme of 650 turns per day, in both directions.
- The winder should have a programme with a pause, e.g. switching off at night (8–12 hours). If it does not, switch it off at night yourself but increase the number of turns by about half.
- Continuous winding can cause excessive wear of or damage to the self-winding mechanism and, in exceptional cases, damage to other parts of the movement.
Warning: Protect the watch from shocks, impacts, magnetic fields and temperatures below -10 °C and above 50 °C. ! The recommended service interval is 3 years.
Detailed setting instructions for cal. 75 (SW510M)
Starting the watch
To start the watch, turn the crown in position 0 away from you. Wind it until you feel clear resistance, ideally every morning.
If you do not wear the watch for a long time, we recommend winding it about once a month and letting it run down.
Setting the time
When the seconds hand reaches 12 o'clock, pull the crown out to the second position. This stops the watch; then set the time by turning the crown as follows. Turn the hands clockwise, first setting the minute hand about 5 minutes past the desired time, then go back to the desired time.
To restart the watch and keep it working properly and water-resistant after setting, push the crown back into position 0.
For the chronograph to work properly, the watch must be running and the crown must be in position 0.
To start and stop the chronograph, press pusher A.
The chronograph can only be reset to zero when it is stopped, by pressing pusher B.
Seconds are shown by the large central seconds hand, and minutes by the counter (sub-dial) at 3 o'clock.
Recommendation ! Do not use the pushers when the watch is wet or exposed to water – water could get inside. ! Protect the watch from shocks, impacts, magnetic fields and temperatures below -10 °C and above 50 °C. ! The recommended service interval is 3 years.
Swiss automatic movement cal. 76 (Sellita SW330-2)
On watches with a screw-down crown, first unscrew the crown by turning it towards you.
To start the watch, turn the crown in position 0 away from you (5-10 turns). After that, it winds itself with the movement of your wrist.
Setting the time
On watches with a screw-down crown, first unscrew the crown by turning it towards you.
When the seconds hand reaches 12 o'clock, pull the crown out to the second position. This stops the watch; then set the time by turning the crown. Turn the hands clockwise, first setting the minute hand about 5 minutes past the desired time, then go back to the desired time.
On watches with a date, first move the hands past 12 o'clock. Whether or not the date changes tells you if the watch is showing morning or afternoon.
To restart the watch and keep it working properly and water-resistant after setting, push the crown back into position 0. On watches with a screw-down crown, screw it back down.
Setting the date
Before setting the date, make sure the watch is not showing a time between 20:00 and 3:00. Otherwise the date might not change over at midnight.
To set the date, pull the crown out to the first position and turn it away from you.
To keep the watch working properly and water-resistant after setting, push the crown back into position 0. On watches with a screw-down crown, screw it back down.
Setting the 24-hour hand (GMT/UTC)
The hand makes one full revolution every 24 hours and lets you follow a second time zone. When set to the same time zone as the main time, it shows whether it is morning or afternoon.
To set the 24-hour hand on its own, pull the crown out to the first position and turn it towards you.
To keep the watch working properly and water-resistant after setting, push the crown back into position 0. On watches with a screw-down crown, screw it back down.
If you do not wear the watch for a long time, we recommend getting it going about once a month by wearing it or winding it with the crown (10–15 turns). We recommend full manual winding only occasionally.
If you use a watch winder, we recommend following these guidelines:
- Choose a programme of 700-800 turns per day, in both directions.
- The winder should have a programme with a pause, e.g. switching off at night (8–12 hours). If it does not, switch it off at night yourself but increase the number of turns by about half.
- Continuous winding can cause excessive wear of or damage to the self-winding mechanism and, in exceptional cases, damage to other parts of the movement.
Protect the watch from shocks, impacts, magnetic fields and temperatures below -10 °C and above 50 °C. The recommended service interval is 3 years.
Resetting the chronograph hands to zero
Example:
One of the chronograph hands is not at zero and needs to be adjusted (e.g. after a battery replacement)
- Pull the crown out to position III
- Press pushers A and B together for at least 2 seconds (the seconds hand turns through 360° → correction mode is active)
Setting the seconds hand
Short press of pusher A – moves the hand one step
Long press of pusher A – moves the hand continuously
Press pusher B to move on to the next setting
Setting the hour hand – on the 5030.D movement the indicator is at the 6 o'clock position
Short press of pusher A – moves the hand one step
Long press of pusher A – moves the hand continuously
Press pusher B to move on to the next setting
Setting the minute hand (indicator at the 9 o'clock position)
Short press of pusher A – moves the hand one step
Long press of pusher A – moves the hand continuously
Then return the crown to position I.
The chronograph adjustment is complete (it can be done at any time)
About the movements
Miyota 8215
If the seconds hand on your watch seems to stick, rest assured that this is not a defect but perfectly normal. In watches fitted with the Miyota 8215 movement, the seconds hand moves in this characteristic way because they use a so-called indirect drive system – Indirect Drive. This is not a fault with the watch; it comes from the design of this movement, which was built this way. The movement has its own safety mechanism which, when the watch is shaken, makes the seconds hand shift and stop. The hand then starts moving again. The jumping of the seconds hand has no effect on the accuracy of the watch.
Miyota 8215 (8205, 8217, 9015 and others)
The manufacturer is gradually changing the design of its movements in other models we currently use as well. A watch model with the same reference may therefore be fitted with a movement in the original version or in the updated design. The new movement system was developed not only for even more accurate timekeeping but above all to protect the mechanism itself from shocks, vibrations and impacts. Even so, it is important to remember that this is a delicate mechanism that needs to be handled with care.
ETA F06.412 movements
PreciDrive
PreciDrive technology redefines typical accuracy standards at +/- 10 seconds a year. The quartz crystal and the integrated circuit (IC) are now sealed in a ceramic housing that protects them from moisture. Thermocompensation controls and regulates the motor pulses according to changes in ambient temperature, which means that PreciDrive meets the strict requirements of COSC chronometer certification (Contrôle Officiel Suisse des Chronomètres). All this provided the watch is not exposed to impacts and is kept at a temperature between 20 °C and 30 °C.
It is a unique achievement that brings real added value to the watch.
HeavyDrive
The exclusive HeavyDrive integrated circuit provides shock protection and widens the scope for balancing the movement of the hand. The weight of an innovatively designed hand or hand material is no longer an obstacle, as HeavyDrive can cope with an imbalance of over 200 % for a traditional seconds hand and 20 % for a traditional minute hand. The movement's built-in electronics detect and then manage the shock, while the motor generates a counter-pulse that locks the hand in position during the shock. This intelligent shock management prompts the motor to react within a fraction of a second whenever a certain shock threshold is exceeded. The energy used to counter this force remains minimal, so the movement's autonomy is preserved.
When not to change the date on your watch?
The time between nine in the evening and three in the morning is when the date on a watch should not be changed.
Winding a mechanical watch and setting the time seems simple. But did you know that something as simple as changing the date at the wrong time can damage your movement? There are times when it is not a good idea to change the date on your watch. So when should you leave it alone? As a general rule, you should know at least two things about setting the time on a mechanical watch. First, always make sure you turn the hands clockwise. Second, do not set the date within 3 hours of midnight. That is all!
There is a period when it is not a good idea to change the date on your watch. It is known as the “danger zone” – the time when the automatic date-change mechanism is engaged, usually between 21:00 and 3:00. During this time, trying to set the date manually can disturb the delicate gear wheels responsible for changing the date, which can knock them out of adjustment or damage them. We recommend changing the date when the hour hand is somewhere in the lower half of the dial; to be on the safe side, change the date around 5:00 (morning or evening).
So why is it bad to change the date during this period?
All the mechanical parts used to change the date work together to build up energy and torque, a process that starts at around 21:00. On some watches with a conventional date and day change mechanism, they remain engaged until about 3:00 in the morning. Using the quick-set date function during this window therefore puts a strain on the gear wheels that the watch is not designed for. A separate system is responsible for driving the date wheel forward during manual setting. Doing so can damage the automatic date and day change mechanism, which usually operates around midnight. That is why it is best to keep the hour hand towards the lower part of the dial before you start changing the date.
The best time to change the date on your watch
As mentioned above, the date should be changed when the hands are somewhere in the lower part of the dial. To be precise, the best time to change the date is around five o'clock, morning or afternoon – it does not matter which. When the watch shows 5:00 in the morning, the conventional date-change mechanism is fully disengaged, and semi-instantaneous and instantaneous mechanisms disengage much earlier. At 17:00, on the other hand, none of the date-change mechanisms has yet started building up power and torque.
How to care for automatic/mechanical watches?
Manual winding
With normal wear, an automatic watch winds itself through the movement of your wrist. However, if you do not wear it for a while and it stops, you will need to set the time and wind it by hand before wearing it again. Simply turn the crown about 20 times towards 12 o'clock.
Power reserve and watch winders
Every automatic movement has a certain power reserve. The watch needs to be worn for at least 8 to 10 hours a day to keep the manufacturer's stated power reserve at its maximum. If you put the watch aside for longer than its current power reserve, it will stop, and you will need to set it again before wearing it. For example, if you take off a watch with a 28 to 42-hour power reserve on Friday evening, it will no longer be running on Monday morning. If you do not wear the watch every day and want to avoid setting the time again and again, you can buy a watch winder from us. The winder keeps the watch moving and so keeps it wound. On Friday evening, simply place the watch in the winder and set the rhythm you want. The watch is wound over the weekend and is ready to wear on Monday morning.
Mechanical watches
This type of drive needs more attention than other mechanisms. Always take the watch off your wrist when winding it. Regular service checks should go without saying for these watches, ideally every 2 to 5 years. Keep in mind that these watches are less resistant to knocks and shocks and are also less accurate than battery-powered watches. Mechanical watches need regular winding; automatic ones need to be kept running through activity and wear. The power reserve when fully wound is at least 42 hours, after which the watch needs to be wound again or worn. A full wind does not guarantee the watch will keep running all day if you have a desk job or are not very active – it simply depends on the movements of the arm you wear it on.
Quartz watches – battery replacement
The movement of a quartz watch is powered by a battery, so it does not need winding. The battery does, however, need to be replaced regularly – at the latest when it reaches the end of its life, which is usually two years at most. Always have the battery replaced at an authorised service centre. Never try to replace it yourself at home. Batteries last around 24 months (remember that the watch was made well before you bought it, so the battery may already have been in it for some time). How long it lasts depends on various factors, such as the type of movement. Chronograph watches use more energy than watches without one. Always have a dead battery removed as soon as possible. If it stays inside the watch for too long, it can seriously damage the mechanism.
Water resistance
Water resistance indicates the ability of the watch case to keep out moisture and water. PRIM watches are divided into groups according to their degree of water resistance. The individual levels, including their markings and permitted uses, are shown in the table below.

* models without a screw-down crown are recommended only for showering and occasional surface swimming; for regular swimming, we recommend only models with a screw-down crown
Using your watch in water
With water-resistant watches, it is important that the crown is always pushed in when in contact with water, and that you never operate the pushers or the crown underwater.
- Watches with a screw-down crown – the crown must always be screwed down tightly (otherwise water will get into the watch).
- Never press the chronograph pushers or move the crown in water!
Hard knocks to the watch or its parts (crown, pushers) can weaken its water resistance, as can sudden changes in temperature. The watch's seals wear out over time. For these reasons, it is advisable to have the water resistance checked by a watchmaker every 12-18 months. A water resistance test should also be carried out every time the watch is opened.
Water resistance is tested in a pressure chamber at a constant temperature of 22 °C +/- 2 °C. The test is carried out with the watch at rest, at the declared pressure, for a set period of time. Every watch therefore meets its declared water resistance, and the water resistance table shows you how to use it correctly.
Watchmakers specify three common levels of water resistance:
- Watches water-resistant to 3ATM, 30 m (3 bar)
They are moisture-proof and dust-proof but should not be exposed to moisture for long periods. They will cope with rain or hand-washing, but definitely do not go swimming with them. - Watches water-resistant to 5ATM, 50 m (5 bar)
They are sealed for everyday use and for accidental contact with water when washing your hands or at the water's surface. However, they should not be exposed to water for long periods. - Watches water-resistant to 10ATM, 100 m (10 bar)
With a SCREW-DOWN CROWN they are designed for intensive and long swims, recreational snorkelling and diving into water. Without a SCREW-DOWN CROWN they are recommended for showering and occasional swimming (but not for recreational snorkelling or diving into water).
For diving to greater depths, special diving watches with a higher declared water resistance of 20ATM, 30ATM, 50ATM etc. must be used.
Contact with salt water
If you go swimming in the sea with your watch, we recommend rinsing it afterwards with drinking water to wash off any salt deposits. After returning from holiday, it is best to visit an authorised service centre and have the watch cleaned ultrasonically – this removes the remaining salt particles, which are not good for your watch.
Sudden temperature changes
No watch copes well with sudden changes in temperature. That is why we strongly advise against taking it into a sauna or steam room. When showering or swimming with a water-resistant watch, it is important to avoid sudden changes in water temperature. If you are heading into the sea with your watch in summer, for example, wet it with water first to soften the thermal shock.
Servicing and cleaning
Regular servicing and ultrasonic cleaning
Mechanical movements need regular maintenance and checks at authorised service centres – this is the only way to ensure accurate timekeeping within the tolerance permitted for the model or brand. Compared with quartz movements, mechanical watches are much more sensitive to factors such as gravity, knocks during everyday use, magnetism, vibration and changes in temperature. If the watch gains or loses noticeably, we recommend visiting an authorised service centre. As with quartz watches, it is a good idea to have mechanical watches cleaned ultrasonically at least once every 1-3 years.
Ultrasonic cleaning
An authorised service centre will not only replace the battery and check the watch's seals but can also clean the case and bracelet in an ultrasonic bath. To keep your watch looking its best, it is a good idea to have it cleaned this way at least once a year. Ultrasonic treatment not only removes all dirt from the case and bracelet but also extends the life of the watch, especially its moving parts. This applies doubly to the bracelet, as dirt that builds up inside can cause excessive friction between the individual links and damage them.
Caring for watch straps and bracelets
The strap is the part of the watch under the most strain – it comes into contact with sweat, water and mechanical friction. Proper care significantly extends its life and keeps the whole watch looking good.
If you plan to use your watch in water or you sweat heavily, definitely avoid a leather strap. Leather and water do not get along, so steel or rubber straps are a better choice in this case. Under normal conditions of use, a leather strap lasts about a year to a year and a half. After that, we recommend replacing it with a new one. The suppleness and colour of leather are affected mainly by moisture, skin acidity, sweat, chemicals, sunlight and the degree of wear.
Basic rules for all types
- wipe the strap with a dry or slightly damp cloth when needed
- avoid prolonged exposure to moisture and high temperatures
- never dry it on a radiator, in direct sunlight or with a hairdryer
- after intense activity, let the strap dry off your wrist
- the strap is a consumable part with a limited life; its warranty is reduced to 6 months
Leather straps
- do not immerse in water; keep contact with water to a minimum
- remove dirt with a slightly damp cloth
- once dry, apply a leather conditioner or cream
- a waterproofing spray can be used for extra protection
FKM / silicone straps
Modern synthetic materials are durable and suitable for sport
- they withstand water, sweat and UV light
- they can be rinsed with lukewarm water and mild soap
- always rinse with clean water after contact with salt water
- check for any cracks
NATO and fabric straps
- hand-wash in lukewarm water with a mild detergent
- rinse thoroughly
- leave to air-dry
Metal bracelets
- clean with lukewarm water, mild soap and a soft brush
- dry thoroughly after cleaning
- rinse with fresh water after contact with salt water
- occasional professional cleaning as part of a watch service is advisable
Extra practical tips
- do not fasten the strap too tightly on your wrist
- consider replacing it if it shows signs of wear (cracks, odour)
- alternating straps makes them last longer
- for water, choose metal or synthetics rather than leather
Crystal materials and types
Mineral crystal (silicate glass)
This is the crystal most commonly used on PRIM watches. Its main advantage is value for money. Another advantage is that it is easier to work than sapphire crystal. It is not as hard as sapphire but is tough enough for everyday wear. Mineral crystal has a further advantage: it refracts light at a much softer angle than sapphire crystal.
Sapphire crystal
Many PRIM models use sapphire crystal (where a model does not have one, we can make a sapphire crystal to order). It is synthetic sapphire – clear corundum – which is highly scratch-resistant (though sapphire crystal can still be scratched or broken in everyday wear). On the Mohs scale, sapphire has a hardness of 9, just one level below diamond.
Today, sapphire crystal is the material of choice for many types of watches. As technology has developed, these crystals can be given an anti-reflective treatment. This means coating the crystal with an anti-reflective layer on one or both sides.
Domed (convex) crystal
If you have bought a watch with a domed (convex) crystal, it is important to look after it properly. Domed crystals are more susceptible to knocks, scuffs and scratches of all kinds. Even with a desk job, you may accidentally knock the watch against the corner of a table, a door frame or a wall without noticing. The crystal may not crack straight away, but with changes in temperature and pressure it can crack hours or even days later. All our crystals are tested, and every watch undergoes a pressure test before it is sold.
1. Classic domed crystals
They look like a classic lens with a single radius of curvature.
2. Non-standard domed crystals (Diplomat, Retro Automatic models, etc.)
The crystal is not domed in the classic way but arched like a vault – simply a vaulted crystal. Crystals like this were most common in the past and were made of acrylic (for example on old PRIM models). Acrylic was flexible but scratched very quickly, so the watch did not look good. That is why today we use mineral crystal, which is highly scratch-resistant but not as flexible as acrylic.
Tritium vs luminous coating
The tritium vials that glow on the indices and hands of our PRIM Sport Tritium watches behave differently from standard technologies such as luminous paint. A layer of luminous paint or tritium vials makes the indices stand out in low light or in the dark. The classic luminous paint mixture is applied in various layers. This affects brightness and how long it glows – that is, how it emits the light it has absorbed from another light source. Luminous paint glows very intensely right after being charged, unlike tritium vials – see the photo taken just after charging, within about 1 minute. The watches with tritium are at the top and on the right.
After a few minutes, both variants glow about the same. See the photo taken about 5 min. after charging.
The third shot shows the luminous indices barely glowing, unlike the tritium vials. See the photo taken about 25 min. after charging.
And so it continues. The luminous indices emit less and less light, while the tritium vials keep glowing at the same intensity. With luminous indices, of course, it matters what kind of light they are charged with – artificial light or sunlight – and for how long. All of this affects how brightly they glow.
The last shot was taken 15 hours after charging.
The watches were exposed to artificial light for about 30 seconds, and the luminous glow is proportionate to that.
Sweeping and silent movement
Clocks and alarm clocks with a sweeping movement (three-hand) are characterised by a seconds hand that moves smoothly – it does not “jump” and therefore does not tick. This is sometimes wrongly described as a “silent movement”, but that term is misleading. Sweeping movements also make a quiet sound, and how loud it is depends both on the design of the movement and on the surface the clock hangs on or the alarm clock stands on.
Regular care and servicing will extend the life of your watch. Contacts for servicing and advice can be found at www.prim.cz. You can also find us at our boutiques in Prague, Nové Město nad Metují and Frýdek-Místek.